Search Results

From November 1970 through August 1971 an extensive program of static and dynamic air cushion inflation tests utilizing human volunteers was conducted at Holloman Air Force Base, New Mexico, sponsored by the Department of Transportation. Forty-one full cushion deployment static firings were made, with air cushion hardware and seating buck environment designed by General Motors. The static series was followed by 35 dynamic sled firings of human volunteers, beginning at 8.6 g (15.1 mph) and culminating at 21.7 g (31.5 mph). A major objective of both the static and dynamic test series was to identify changes in air-cushion design found necessary to improve its protective capability for human beings. Because of the severity of cushion deployment, one modification was made following the initial static tests: The orifice diameter size of the bag inlet was reduced from 1.0 to 0.6 in to diminish the rapidity of bag inflation. This modification proved effective in the dynamic series.

A search for methods of switching a proposed three beam headlight system led to the evaluation of 41 possible schemes. Human factors criteria reduced the original 41 to three systems which were tested in a laboratory with a broad range of subjects. Recordings of practice trials, learning trials, and the responses to visual cues projected on a screen were analyzed. The same test procedure was also used to compare three alternative ways of switching conventional two beam headlight systems. Summary data is presented for the six systems tested grouped by test subject age, sex, and driving experience. The most pronounced difference observed was in the subjective preference rating among two beam switching systems. All systems tested resulted in remarkably few learning and practice trials. Small differences were recorded among systems in operational response time.

The Paint Technology Globalization effort is recognized as an important step of accomplishing the leveraging of worldwide resources of both engineering and purchasing in order to improve General Motor's competitiveness. The process used, the benefits derived, the current status of the effort, and the expected results (deliverables) are discussed. These include common materials, processing, and equipment paint specifications to be included in purchasing bid packages.

The purpose of this paper is to provide an overview of the process of selection, development and approval of General Motors original equipment TPC passenger car tires. We have attempted to minimize detail in each specific area, but intend to provide a general comprehension of the thought processes involved and the procedures used to select the proper tire size and type for a vehicle. We will then describe the tire performance criteria involved in the overall development and approval process and will subsequently consider tire noise requirements in somewhat greater detail. The paper will conclude by describing the General Motors Tire Performance Criteria (TPC) System, which is a documentation of the General Motors Tire Performance requirements and test procedures.

FIGURE 1 The 200 HP high performance 4.3L Vortec V6 engine has been developed to satisfy the need for a fuel efficient performance powerplant in the General Motors small truck platforms. Marketing requirements included strong low and mid range torque, relatively high specific power, smoothness and noise comparable to the best competitive six cylinder engines, excellent driveability, and a new technology image. Maintaining the 4.3L engine record of high reliability and customer satisfaction was an absolute requirement. Fuel economy and exhaust emission performance had to meet expected customer and legislated requirements in the mid 1990's.

Free form fabrication, or rapid prototyping as it is commonly known, is the creation of a physical entity, directly from numerical description, using an additive process. The mathematical data used is typically in the form of a 3D CAD file, but it may also be obtained from a reverse engineering process. This paper presents a review of three of the leading FFF (free form fabrication) systems which are commercially available. Time constraints will allow us to describe only three of these products. Although this does not do justice to a technology where there are more than 30 different systems in various stages of development, these examples represent the vast majority of machines which are in the marketplace today.

Today's world places increased emphasis on society's members to know more, to do more, to see more. Increasingly, information is thrown to the consumer that he/she has to process almost continually, regardless of their surroundings. Due to this heightened need, the customer is becoming increasingly perceptive of their vehicle surroundings, expecting their vehicle to be an extension of their home and/or office, to assist in getting things done in an environment that is as convenient and comfortable as their primary workplace. Similarly, there is also increased emphasis on vehicles to be styled so that they are visually appealing, so that all the parts work as a whole to make the environment as enjoyable as consumers' most pleasant surroundings outside the vehicle.

Reducing the wall thickness of automotive fascia offers cost and weight savings over those manufactured today. New high performance RIM polyurethane/urea and polyurea polymers with improved mechanical properties over conventional systems make down-gauging possible while maintaining specified performance.1 Adding low cost, high surface quality fillers to these polymers provides enhanced dimensional stability in fascia at reduced wall thickness, thus meeting ever increasing demands for lower cost and high quality. This paper describes validation studies of filled RIM fascia down-gauged 22% to 3.0 mm wall thickness and compares them to conventional fascia moulded at nominal 3.9 mm wall thickness. High performance polyurethane/urea, polyurea, and conventional polyurethane/urea each incorporating wollastonite, mica, or milled glass were tested. The data include “on-car position” moisture stability, painted impact at low temperature, and material processing.

Fatal crash circumstances for 48 belted female drivers were studied in-depth and compared to those of 83 belted male drivers in a similar population of vehicles. Women had a higher incidence of crashes on slippery roads, during lane changes and passing maneuvers than men who had a higher rate of aggressive driving and speed related crashes (χ2 = 10.47, p < 0.001). Driver-side damage was significantly more frequent in female than male crashes (χ2 = 5.74, p < 0.025) and women had a higher fraction of side impacts (45.9% v 31.4%) and crashes during daylight (87.0% v 72.3%, χ2 = 3.65, p < 0.05) than men. Women also had a higher fraction of potentially avoidable crashes than men (57.5% v 39.0%) and a lower involvement related to aggressive driving (10.6% v 25.6%). These differences were statistically significant (χ2 = 5.41, p < 0.025).

Finite element analysis (FEA) predictions of magnesium beams are compared to load versus displacement test measurements. The beams are made from AM60B die castings, AM30 extrusions and AZ31 sheet. The sheet and die cast beams are built up from two top hat sections joined with toughened epoxy adhesive and structural rivets. LS-DYNA material model MAT_124 predicts the magnesium behavior over a range of strain rates and accommodates different responses in tension and compression. Material test results and FEA experience set the strain to failure limits in the FEA predictions. The boundary conditions in the FEA models closely mimic the loading and constraint conditions in the component testing. Results from quasi-static four-point bend, quasi-static axial compression and high-speed axial compression tests of magnesium beams show the beam's behavior over a range of loadings and test rates. The magnesium beams exhibit significant material cracking and splitting in all the tests.

A deformable finite element dummy model was used to simulate air bag interaction with in-position passenger side occupants in frontal vehicle crash. This dummy model closely simulates the Hybrid III hardware with respect to geometry, mass, and material properties. Test data was used to evaluate the validity of the model. The calculated femur loads, chest acceleration and head acceleration were in good agreement with the test data. A semi-rigid dummy model (with rigid chest) was derived from the deformable dummy to improve turnaround time. Simulation results using the semi-rigid dummy model were also in reasonable agreement with the test data. For comparison purpose, simulations were also performed using PAMCVS, a hybrid code which couples the finite element code PAMCRASH with the rigid body occupant code. The deformable dummy model predicted better chest acceleration than the other two models.

The potential of bake hardenable steel as a substitute for SAE 1008 steel to reduce gage and improve dent resistance is investigated in this report. Outer body panels in particular are susceptible to palm printing and other forms of denting. Conventional SAE 1008 steel and a developmental continuous annealed bake hardenable steel from Inland Steel Company are compared for dent performance properties. Bake hardenable (BH) steel is a medium strength (200-350 MPa) steel that receives an increase in yield strength during the heating of the paint bake cycle. An increase in yield strength would result in an increase in dent resistance. The increase in dent resistance is more quantitatively evaluated by comparing the BH steel with the current production material (SAE 1008) of a rear compartment lid outer.

Fully Flexible Valve Actuation (FFVA) systems provide maximum flexibility to adjust lift profiles of engine intake and exhaust valves. A research grade electro-hydraulic servo valve based FFVA system was designed to be used with an engine in a test cell to precisely follow desired lift profiles. Repetitive control was chosen as the control strategy. Crank angle instead of time is used to trigger execution to ensure repeatability. A single control is used for different engine speeds even though the period for one revolution changes with engine speeds. The paper also discusses lift profile extension, instantaneous lift profile switching capability and built-in safety features.

Casting, machining and structural simulations were completed on a V8 engine block made in Compacted Graphite Iron (CGI) for use in a racing application. The casting and machining simulations generated maps of predicted tensile strength and residual stress in the block. These strength and stress maps were exported to a finite element structural model of the machined part. Assembly and operating loads were applied, and stresses due to these loads were determined. High cycle fatigue analysis was completed, and three sets of safety factors were calculated using the following conditions: uniform properties and no residual stress, predicted properties and no residual stress, and predicted properties plus residual stress.

This paper describes the hardware execution of the front and rear suspensions of the all new 1997 Chevrolet Corvette. Topics covered include: alternative design trade-off, mass optimization, alignment and trim, structural interfaces, shared components, component design and a review of the overall design of the front and rear suspensions. Two case studies are detailed for the front upper and rear lower control arms. The systems engineering process used for suspension design is described throughout the paper.

The rear cross-car stiffener subsystem is generally located at the underside of the rear compartment pan of a car body and connects the two rear longitudinal rails or rear rockers. The primary purpose of this subsystem is to maintain structural integrity as well as fuel system integrity in a rear angle impact or dynamic side impact collision. To evaluate the effect of this subsystem on lateral crashworthiness in a high speed angle impact, a finite element model consisting of the cross-car bar, a portion of rear compartment pan and both rear rails was developed and analyzed with the DYNA3D crashworthiness simulation software. Thus, the cross-car stiffener subsystem design including the welding pattern was finalized and the acceptable design was successfully implemented in the vehicle. Subsequently drop silo tests were carried out to further verify the design and to improve the manufacturing process.

Casting technology developmentshave led to a manufacturing process that allows the casting of thin wall (2-3mm) heat resistant ferritic stainless steel exhaust manifolds which can replace stamped and tubular weldments as well as iron castings where temperature requirements are increased. This casting process combines the thin wall and clean metal benefits of the counter gravity, vacuum-assist casting process using thin, light-weight bonded sand molds supported by vacuum-ridgidized sand. This combination is called the LSVAC (Loose Sand Vacuum Assisted Casting) process, a patented process. This process will significantly contribute to the growth of near-net shape steellstainless steel castings for automotive and allied industries. For exhaust manifolds, a modified grade of ferritic stainless steel with good oxidation resistance to 950°C in high dew point synthetic exhaust gas atmospheres was developed.

The primary objective of Central Port Fuel Injection is to be a low cost multi-point fuel injection system with the additional attributes of compactness, packaging flexibility, and reliability. Performance of this fuel system closely resembles that of a simultaneous multi-point fuel injection system in flow control, dynamic range, cylinder-to-cylinder distribution, idle quality, transient response, and emissions. The system provides significantly improved performance in the areas of hot fuel handling, cold startability, vacuum and voltage sensitivity and system noise. This performance comes at a significant cost savings and greater packaging and targeting flexibility over a conventional multi-point fuel injection system.

An objective, biomechanically based assessment is made of the risks of life-threatening brain injury of frontal crash test results. Published 15 ms HIC values for driver and right front passenger dummies of frontal barrier crash tests conducted by Transport Canada and NHTSA are analyzed using the brain injury risk curve of Prasad and Mertz. Ninety-four percent of the occupants involved in the 30 mph, frontal barrier compliance tests had risks of life-threatening brain injury less than 5 percent. Only 3 percent had risks greater than 16 percent which corresponds to 15 ms HIC > 1000. For belt restrained occupants without head contact with the interior, the risks of life-threatening brain injury were less than 2 percent. In contrast, for the more severe NCAP test condition, 27 percent of the drivers and 21 percent of the passengers had life-threatening brain injury risks greater than 16 percent.

This paper describes the results of an ongoing project in the GM Motorsports Safety Technology Research Program to investigate Indianapolis-type (Indy car) race car crashes using an on-board impact recorder as the primary data collection tool. The paper discusses the development of specifications for the impact-recording device, the selection of the specific recorder and its implementation on a routine basis in Indy car racing. The results from incidents that produced significant data (crashes with peak decelerations above 20 G) during the racing seasons from 1993 through the first half of 1998 are summarized. The focus on Indy car crashes has proven to provide an almost laboratory-like setting due to the similarity of the cars and to the relative simplicity of the crashes (predominantly planar crashes involving single car impacts against well-defined impact surfaces).